It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.

If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.

Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>

This reverts commit 0ebf9842.

Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.

Next commit introduces new generic implementation of
fastboot_set_reboot_flag.

Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>

For printing unsigned int %u has to be used.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS

Pull request for UEFI sub-system for efi-2021-04-rc2

Bug fixes:

* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle

Documentation:

* man-page for load command
* describe end of life of plat_auto

Describe when plat_auto is freed.

Fix a typo.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

If the exception cannot be raised, the command returns.
Currently the return values are not all the same.

Remove the sub-chapter 'Return value'

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Man-page for load command.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

The Load File2 protocol exposes a device path with a VenMedia() node. Hence
our implementation of the device path to text protocol should support this
node.

Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

If dtbdump.efi is loaded from memory when calling LoadImage the loaded
image protocol will not indicate the partition from where it was loaded.
In this case use the EFI system partition for the 'load' and 'save'
commands.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

On the handle for the UEFI System Partition we must install the System
Partition GUID (with a NULL interface).

Let the efidebug command display the GUID.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

In the implementation of the EFI_DT_FIXUP_PROTOCOL:

* Only check the buffer size when EFI_DT_APPLY_FIXUPS is set.
* In this case the field totalsize of the device-tree may not exceed the
  buffer size.
* Install device-tree only if EFI_DT_INSTALL_TABLE is set.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Sync all AM65 related v5.11-rc6 Linux kernel dts into U-Boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Add configs for voltage switching and UHS modes for the SD card
and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.

Disable UHS modes for this board until a new board revision fixes
the issue.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add the appropriate itapdly and clkbuf-sel values required for
some lower speed modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add support for the main_gpio0 node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Add support for regulators to power cycle and switch IO voltage to the
SD card. This enables support for UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Update otap delay values to match with the latest Data Manual[1].

[1] https://www.ti.com/lit/gpn/dra829v



Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts

This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode

While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.

To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.

Use the sdhci writeb callback to implement this condition.

[1] http://www.ti.com/lit/gpn/am6546

 Section 5.10.5.16.1

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.

[1] https://www.ti.com/lit/pdf/spract9



Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.

Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.

Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Convert the flags field defines to use the BIT() macro.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

With commit 38d6b7eb ("spl: Drop bd_info in the data section") you
need to enable this option to boot from mmc.

Signed-off-by: Dario Binacchi <dariobin@libero.it>

The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.

The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
  lockstep-mode => ti,cluster-mode
  atcm-enable   => ti,atcm-enable
  btcm-enable   => ti,btcm-enable
  loczrama      => ti,loczrama

Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.

Signed-off-by: Suman Anna <s-anna@ti.com>

AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.

Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

This disables booting to non-Linux OSes.

This board is uncomfortably close to its 256K size limit, so every
few KB saved helps.

Signed-off-by: David Lechner <david@lechnology.com>

This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.

This also fixes the warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: David Lechner <david@lechnology.com>